June 05, 2020

KitchenAid KOCE507E Microwave Oven INSTALLATION INSTRUCTIONS ELECTRIC COMBINATION

KitchenAid KOCE507E Microwave Oven INSTALLATION INSTRUCTIONS ELECTRIC COMBINATION - page 7

7

1.  Connect the 2 black wires (C) together using a UL Listed wire 

connector.

2.  Connect the 2 white wires (D) and the green (or bare) ground 

wire (of the oven cable) using a UL Listed wire connector.

3.  Connect the 2 red wires (G) together using a UL Listed wire 

connector.

4.  Install junction box cover.

Install Oven

1.  Using 2 or more people, lift oven partially into cabinet cutout. 

Use the oven opening as an area to grip.

NOTE: Push against seal area of oven front frame when 

pushing oven into cabinet. Do not push against outside edges.

2.  Push against the seal area of the front frame to push the 

oven into the cabinet until the back surface of the front frame 

touches the front wall of the cabinet.

3.  Push oven completely into cabinet and center oven into 

cabinet cutout.

4.  Remove the tape from black front trims.

 

Securely fasten the oven to the cabinet using the #8-14 x 

¾" screws provided.

 

Insert the screws through hole in black trim aligning  

with hole in oven frame. Do not overtighten screws.

A

B

C

A.  Oven frame

B.  Oven frame hole

C.  Black trim piece

5.  The bottom vent is shipped in the foam packing at the top  

of the oven. Install the bottom vent (C) as follows:

 

Align vent tab (B) with oven frame (A) as shown.

 

Using one #8-18 x 

3

/

8

" screw (D) on each side of the vent 

tab (B), fasten the vent securely to the oven.

6.  Replace oven racks.

7.  Replace the oven door. See the “Replace Oven Door(s)” 

section.

8.  Check that door is free to open and close. If it is not, repeat 

the removal and installation procedures. See the “Prepare 

Built-In Microwave/Oven Combination” section.

9.  Reconnect power.

10. The display panel will light briefly, and “PF” should appear in 

the display.

11. If the display panel does not light, please reference the 

“Warranty” section of the Use and Care Guide.

Install Warming Drawer Deflector Kit 

(Only for Ovens Installed Above Warming 

Drawers)

On combo microwave/oven models installed above a warming 

drawer, a warming drawer deflector kit must be installed. See  

the “Tools and Parts” section for ordering information.

Parts Supplied

A

B

D

C

A.  Oven frame

B.  Vent tab

C.  Bottom vent

D.  #8-18 x 

3

/

8

" screws

B

A

A.  Phillips head screws (4)  

only 2 screws for 27" (68.6 cm) size

B.  Warming drawer deflector (1)




7 1.  Connect the 2 black wires (C) together using a UL Listed wire  connector. 2.  Connect the 2 white wires (D) and the green (or bare) ground  wire (of the oven cable) using a UL Listed wire connector. 3.  Connect the 2 red wires (G) together using a UL Listed wire  connector. 4.  Install junction box cover. Install Oven 1.  Using 2 or more people, lift oven partially into cabinet cutout.  Use the oven opening as an area to grip. NOTE: Push against seal area of oven front frame when  pushing oven into cabinet. Do not push against outside edges. 2.  Push against the seal area of the front frame to push the  oven into the cabinet until the back surface of the front frame  touches the front wall of the cabinet. 3.  Push oven completely into cabinet and center oven

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

About The Author

Related posts